Verification error first mismatch at byte 0x0000 0x62 0x0c

Arduino.ru

Регистрация новых пользователей и создание новых тем теперь только на новом форуме https://forum.arduino.ru

forum.arduino.ru

Ошибка avrdude: verification error

Еще вчера ардуина работала, а сегодня вдруг перестала. Теперь при подключении к ПК постоянно мигает встроенные светодиод на 13 пине.

подключаете usbasp к nano (разъем на 6 штырьков — mosi(D11), miso(D12), sck(D13), reset, vcc, gnd), выбираете в IDE програматор usbasp, выбираете плату , и жмете записать загрузчик

подключаете usbasp к nano (разъем на 6 штырьков — mosi(D11), miso(D12), sck(D13), reset, vcc, gnd), выбираете в IDE програматор usbasp, выбираете плату , и жмете записать загрузчик

так вроде все понял, спасибо.

сделал как ты сказал но выдает ошибку при нажатии на «записать загрузчик»

Подключил вроде все как надо в соответствии с этими данными:

Собственно как я понял, надо обновить прошивку на программаторе? Но как это сделать не имея нечего кроме самого программатора я чето не вкурил, хотя гугл юзал. у меня ардуина которая не может залить в себя скетч, следовательно ее не получится использовать для прошивки программатора.

лучше прямо на пины подключайте, а то у меня на нане другой расклад на 6 пиновом разъеме, чем у вас на рисунке, на usbasp такой же

на эту ошибку не обращайте внимание «avrdude: warning: cannot set sck period. please check for usbasp firmware update.«,

лучше прямо на пины подключайте, а то у меня на нане другой расклад на 6 пиновом разъеме, чем у вас на рисунке, на usbasp такой же

на эту ошибку не обращайте внимание «avrdude: warning: cannot set sck period. please check for usbasp firmware update.«,

А я ведь сначала подумал что надо на пины, но потом перечитал про 6ти контактный разъем и не стал уточнять 😀 хотя перед этим нарисовал схему тк были вопросы:

1) какой reset выбрать, на стороне A или на стороне D пинов? я склоняюсь к ресету на стороне питания, но лучше уточнить.

2) какую землю выбрать, на программаторе это предпоследняя определил опытным путем, а вот какая на плате опять такие со стороны A или со стороны D пинов? хотя тут вроде логично землю выбрать рядом в +5v но на всякий случай лучше спрашиваю.

Источник

Verification error after loading code by Serial #71

Comments

Hi! I’m building my project on Atmega128 chip using your bootloader. Bootloader was load properly by USBASP and I even can see it in FLASH through Avrdude terminal mode from address 0xFC00 (as I remember). Then I faced an issue during loading my program by Serial through USB-UART (CH340 chip). It seems that Arduino IDE connects to Atmega and I see Avrdude writing progress bars but then it fails on verification step:

avrdude: verification error, first mismatch at byte 0x0000
0xff != 0x0c
avrdude: verification error; content mismatch

It seems that my sketch code was not recorded to Atmega. If I loading the code through programmer by ICSP — it works well.
Here is the Avrdude log:

/Applications/Arduino.app/Contents/Java/hardware/tools/avr/bin/avrdude -C/Users/dmitrij/Library/Arduino15/packages/MegaCore/hardware/avr/2.0.0/avrdude.conf -v -patmega128 -carduino -P/dev/cu.wchusbserial1420 -b115200 -D -Uflash:w:/var/folders/18/60_7xyc92138x6vhc69t25zc0000gn/T/arduino_build_113404/Blink.ino.hex:i

avrdude: Version 6.3, compiled on Jan 17 2017 at 12:01:35
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2014 Joerg Wunsch

Читайте также:  H96pro 3 32 прошивка

avrdude: AVR device initialized and ready to accept instructions

avrdude: Device signature = 0x1e9702 (probably m128)
avrdude: reading input file «/var/folders/18/60_7xyc92138x6vhc69t25zc0000gn/T/arduino_build_113404/Blink.ino.hex»
avrdude: writing flash (1240 bytes):

avrdude: 1240 bytes of flash written
avrdude: verifying flash memory against /var/folders/18/60_7xyc92138x6vhc69t25zc0000gn/T/arduino_build_113404/Blink.ino.hex:
avrdude: load data flash data from input file /var/folders/18/60_7xyc92138x6vhc69t25zc0000gn/T/arduino_build_113404/Blink.ino.hex:
avrdude: input file /var/folders/18/60_7xyc92138x6vhc69t25zc0000gn/T/arduino_build_113404/Blink.ino.hex contains 1240 bytes
avrdude: reading on-chip flash data:

Reading | ########################################Произошла ошибка при загрузке скетча
########## | 100% 0.34s

avrdude: verifying .
avrdude: verification error, first mismatch at byte 0x0000
0xff != 0x0c
avrdude: verification error; content mismatch

avrdude done. Thank you.

Do you have any thoughts on it?

The text was updated successfully, but these errors were encountered:

Источник

Verification Error on Burning Bootloader #19

Comments

Hi.
I’m getting following Error on burning bootloader using arduino ide:
avrdude: verifying . avrdude: verification error, first mismatch at byte 0xfd00 0xff != 0x09 avrdude: verification error; content mismatch

I get this error on both Atmega64a and Atmega128a using any clock config and any programmer.

The text was updated successfully, but these errors were encountered:

Please turn on verbose upload in the IDE settings and post your full error message. What programmer are you using? This may be a lockbit issue, but I can’t tell before the full error message is posted 😉

`C:\Arduino\hardware\tools\avr/bin/avrdude -CC:\Users\Mehdi\AppData\Local\Arduino15\packages\MegaCore\hardware\avr\1.0.3/avrdude.conf -v -patmega64 -cusbasp -Pusb -e -Ulock:w:0x3f:m -Uefuse:w:0xff:m -Uhfuse:w:0xc6:m -Ulfuse:w:0xbf:m

avrdude: Version 6.0.1, compiled on Apr 15 2015 at 19:59:58
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2009 Joerg Wunsch

avrdude: auto set sck period (because given equals null)
avrdude: AVR device initialized and ready to accept instructions

avrdude: Device signature = 0x1e9602
avrdude: erasing chip
avrdude: auto set sck period (because given equals null)
avrdude: reading input file «0x3f»
avrdude: writing lock (1 bytes):

C:\Arduino\hardware\tools\avr/bin/avrdude -CC:\Users\Mehdi\AppData\Local\Arduino15\packages\MegaCore\hardware\avr\1.0.3/avrdude.conf -v -patmega64 -cusbasp -Pusb -Uflash:w:C:\Users\Mehdi\AppData\Local\Arduino15\packages\MegaCore\hardware\avr\1.0.3/bootloaders/optiboot_flash/atmega64/optiboot_flash_atmega64_115200_16MHz.hex:i -Ulock:w:0x0f:m

avrdude: Version 6.0.1, compiled on Apr 15 2015 at 19:59:58
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2009 Joerg Wunsch

avrdude: 1 bytes of lock written
avrdude: verifying lock memory against 0x3f:
avrdude: load data lock data from input file 0x3f:
avrdude: input file 0x3f contains 1 bytes
avrdude: reading on-chip lock data:

avrdude: verifying .
avrdude: 1 bytes of lock verified
avrdude: reading input file «0xff»
avrdude: writing efuse (1 bytes):

avrdude: 1 bytes of efuse written
avrdude: verifying efuse memory against 0xff:
avrdude: load data efuse data from input file 0xff:
avrdude: input file 0xff contains 1 bytes
avrdude: reading on-chip efuse data:

Читайте также:  Samsung ml 3051 прошивка

avrdude: verifying .
avrdude: 1 bytes of efuse verified
avrdude: reading input file «0xc6»
avrdude: writing hfuse (1 bytes):

avrdude: 1 bytes of hfuse written
avrdude: verifying hfuse memory against 0xc6:
avrdude: load data hfuse data from input file 0xc6:
avrdude: input file 0xc6 contains 1 bytes
avrdude: reading on-chip hfuse data:

avrdude: verifying .
avrdude: 1 bytes of hfuse verified
avrdude: reading input file «0xbf»
avrdude: writing lfuse (1 bytes):

avrdude: 1 bytes of lfuse written
avrdude: verifying lfuse memory against 0xbf:
avrdude: load data lfuse data from input file 0xbf:
avrdude: input file 0xbf contains 1 bytes
avrdude: reading on-chip lfuse data:

avrdude: verifying .
avrdude: 1 bytes of lfuse verified

avrdude done. Thank you.

avrdude: auto set sck period (because given equals null)
avrdude: AVR device initialized and ready to accept instructions

avrdude: Device signature = 0x1e9602
avrdude: NOTE: «flash» memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: auto set sck period (because given equals null)
avrdude: reading input file «C:\Users\Mehdi\AppData\Local\Arduino15\packages\MegaCore\hardware\avr\1.0.3/bootloaders/optiboot_flash/atmega64/optiboot_flash_atmega64_115200_16MHz.hex»
avrdude: writing flash (65536 bytes):

avrdude: 65536 bytes of flash written
avrdude: verifying flash memory against C:\Users\Mehdi\AppData\Local\Arduino15\packages\MegaCore\hardware\avr\1.0.3/bootloaders/optiboot_flash/atmega64/optiboot_flash_atmega64_115200_16MHz.hex:
avrdude: load data flash data from input file C:\Users\Mehdi\AppData\Local\Arduino15\packages\MegaCore\hardware\avr\1.0.3/bootloaders/optiboot_flash/atmega64/optiboot_flash_atmega64_115200_16MHz.hex:
avrdude: input file C:\Users\Mehdi\AppData\Local\Arduino15\packages\MegaCore\hardware\avr\1.0.3/bootloaders/optiboot_flash/atmega64/optiboot_flash_atmega64_115200_16MHz.hex contains 65536 bytes
avrdude: reading on-chip flash data:

avrdude: verifying .
avrdude: verification error, first mismatch at byte 0xfd00
0xff != 0x09
avrdude: verification error; content mismatch

avrdude done. Thank you.

Error while burning bootloader.`

Have you tried using an other programmer? I’ve experienced some issues with the USBasp. The USBtinyISP works just fine

Please try the 1MHz option also. Does this option return the same error?

Yes, I tried 1Mhz option, and returns same error.

Have you tried using an other programmer? I’ve experienced some issues with the USBasp. The USBtinyISP works just fine

I’m actually able to reproduce this exact error using my own USBasp. Personally I prefer to use the USBtinyISP (

3$) instead. It’s ALWAYS working, and I’ll never experienced any issues with it. I’ve had several issues with the USBasp, and that’s why I rarely use it when burning fuses, uploading bootloader or using AVRdude in general 😉

TL;DR
There is an issue with the USBasp, and nothing I can do about it. I suggest you try another programmer

I have same error with USBTinyISP:

C:\Arduino\hardware\tools\avr/bin/avrdude -CC:\Users\Mehdi.BARNAMENEVIS.000\AppData\Local\Arduino15\packages\MegaCore\hardware\avr\1.0.3/avrdude.conf -v -patmega128 -cusbtiny -e -Ulock:w:0x3f:m -Uefuse:w:0xff:m -Uhfuse:w:0xc6:m -Ulfuse:w:0xbf:m

avrdude: Version 6.0.1, compiled on Apr 15 2015 at 19:59:58
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2009 Joerg Wunsch

avrdude: usbdev_open(): Found USBtinyISP, bus:device: bus-0:.\libusb0-0001—0x1781-0x0c9f
AVR Part : ATmega128
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :

Читайте также:  Mysql error no 2014

avrdude: programmer operation not supported

avrdude: Using SCK period of 10 usec
avrdude: AVR device initialized and ready to accept instructions

avrdude: Device signature = 0x1e9702
avrdude: erasing chip
avrdude: Using SCK period of 10 usec
avrdude: reading input file «0x3f»
avrdude: writing lock (1 bytes):

C:\Arduino\hardware\tools\avr/bin/avrdude -CC:\Users\Mehdi.BARNAMENEVIS.000\AppData\Local\Arduino15\packages\MegaCore\hardware\avr\1.0.3/avrdude.conf -v -patmega128 -cusbtiny -Uflash:w:C:\Users\Mehdi.BARNAMENEVIS.000\AppData\Local\Arduino15\packages\MegaCore\hardware\avr\1.0.3/bootloaders/optiboot_flash/atmega128/optiboot_flash_atmega128_115200_16MHz.hex:i -Ulock:w:0x0f:m

avrdude: Version 6.0.1, compiled on Apr 15 2015 at 19:59:58
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
Copyright (c) 2007-2009 Joerg Wunsch

avrdude: usbdev_open(): Found USBtinyISP, bus:device: bus-0:.\libusb0-0001—0x1781-0x0c9f
AVR Part : ATmega128
Chip Erase delay : 9000 us
PAGEL : PD7
BS2 : PA0
RESET disposition : dedicated
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :

avrdude: programmer operation not supported

avrdude: Using SCK period of 10 usec
Writing | ################################################## | 100% 0.00s

avrdude: 1 bytes of lock written
avrdude: verifying lock memory against 0x3f:
avrdude: load data lock data from input file 0x3f:
avrdude: input file 0x3f contains 1 bytes
avrdude: reading on-chip lock data:

avrdude: verifying .
avrdude: 1 bytes of lock verified
avrdude: reading input file «0xff»
avrdude: writing efuse (1 bytes):

avrdude: 1 bytes of efuse written
avrdude: verifying efuse memory against 0xff:
avrdude: load data efuse data from input file 0xff:
avrdude: input file 0xff contains 1 bytes
avrdude: reading on-chip efuse data:

avrdude: verifying .
avrdude: 1 bytes of efuse verified
avrdude: reading input file «0xc6»
avrdude: writing hfuse (1 bytes):

avrdude: 1 bytes of hfuse written
avrdude: verifying hfuse memory against 0xc6:
avrdude: load data hfuse data from input file 0xc6:
avrdude: input file 0xc6 contains 1 bytes
avrdude: reading on-chip hfuse data:

avrdude: verifying .
avrdude: 1 bytes of hfuse verified
avrdude: reading input file «0xbf»
avrdude: writing lfuse (1 bytes):

avrdude: 1 bytes of lfuse written
avrdude: verifying lfuse memory against 0xbf:
avrdude: load data lfuse data from input file 0xbf:
avrdude: input file 0xbf contains 1 bytes
avrdude: reading on-chip lfuse data:

avrdude: verifying .
avrdude: 1 bytes of lfuse verified

avrdude done. Thank you.

avrdude: AVR device initialized and ready to accept instructions

avrdude: Device signature = 0x1e9702
avrdude: NOTE: «flash» memory has been specified, an erase cycle will be performed
To disable this feature, specify the -D option.
avrdude: erasing chip
avrdude: Using SCK period of 10 usec
avrdude: reading input file «C:\Users\Mehdi.BARNAMENEVIS.000\AppData\Local\Arduino15\packages\MegaCore\hardware\avr\1.0.3/bootloaders/optiboot_flash/atmega128/optiboot_flash_atmega128_115200_16MHz.hex»
avrdude: writing flash (131072 bytes):

avrdude: 131072 bytes of flash written
avrdude: verifying flash memory against C:\Users\Mehdi.BARNAMENEVIS.000\AppData\Local\Arduino15\packages\MegaCore\hardware\avr\1.0.3/bootloaders/optiboot_flash/atmega128/optiboot_flash_atmega128_115200_16MHz.hex:
avrdude: load data flash data from input file C:\Users\Mehdi.BARNAMENEVIS.000\AppData\Local\Arduino15\packages\MegaCore\hardware\avr\1.0.3/bootloaders/optiboot_flash/atmega128/optiboot_flash_atmega128_115200_16MHz.hex:
avrdude: input file C:\Users\Mehdi.BARNAMENEVIS.000\AppData\Local\Arduino15\packages\MegaCore\hardware\avr\1.0.3/bootloaders/optiboot_flash/atmega128/optiboot_flash_atmega128_115200_16MHz.hex contains 131072 bytes
avrdude: reading on-chip flash data:

avrdude: verifying .
avrdude: verification error, first mismatch at byte 0x1fc00
0xff != 0x01
avrdude: verification error; content mismatch

Источник

Smartadm.ru
Adblock
detector