No boot drive found error

6 Methods to Fix No Bootable Device on Windows 11, 10, 8, 7

If your computer pops out error message «No bootable devices found», no need to worry about that since this article shows how to fix no bootable device error via 6 different methods in Windows PC.

By Emily / Last Updated September 30, 2022

What does it mean by «no bootable device»?

A bootable device is a kind of storage hardware, such as hard drive, USB flash drive floppy disk drive, DVD, CD-ROM drive, which contains necessary boot files and drivers for loading the operating system. BIOS is a program in computers used to load the operating system and execute the boot operation. The “no bootable device found” error is actually reported by BIOS. It means BIOS cannot find or locate the boot device or the boot files on the boot device are incorrect.

Why does PC say no bootable device?

How to fix no bootable device issue properly on Windows computer? First, let’s find out the possible causes of this problem. Here are some major reasons you can take a look at.

в–¶An incorrect boot order.

в–¶System partition is not set as active.

в–¶Internal hard disk is corrupted due to disk errors/bad sectors.

в–¶Computer’s boot hard disk MBR sector is damaged.

How to fix no bootable device on Windows 11/10/8/7?

Now, you can try the below-listed methods to check if the «no bootable device found» problem can be fixed.

в–Њ Method 1. Remove and connect back all hardware components

At first, you can completely power off your computer, remove all hardware devices, then put them back all properly. That can help check whether the BIOS did not detect the system hard drive due to loose connection and led to «no bootable device» issue. If this does not work for your situation, proceed to the next method.

в–Њ Method 2. Check boot order

An incorrect boot order could mislead your computer to boot from an unbootable hard drive, then the «no bootable device found» will occur. So make sure your system hard drive is in the first place of the boot order.

Step 1. Restart your computer and press a specific key (Del, F2, F10…) to enter BIOS setup.

Step 2. Access the «Boot» tab using the right arrow keys on your keyboard. And move your system hard drive to the top of the boot order list.

в–Њ Method 3. Reset primary partition as active

The partition where the operating system is installed is called as primary partition. It needs to be set as active for an OS boot success. So if it is set as inactive by mistake, the «no boot device found» issue will be triggered. Thus, please set it back as active.

Step 1. Insert the Windows installation DVD into your computer and boot from it. Select the language and keyboard layout, and click on «Repair your computer».

Step 2. If you are using Windows 10 and 8 installation DVD, click «Troubleshoot» and then «Command Prompt». If you are using Windows 7 installation DVD, in the «System Recovery Options» screen, select the first choice «Use recovery tools that can help…», Windows 7 OS and click «Next». Select «Command Prompt» on the subsequent window.

Step 3. In the elevated Command Prompt window, write the following commands one by one and press «Enter» afterward:

в—Џ lit disk
в—Џ select disk 0: 0 is the disk number of the system hard disk.
в—Џ list partition
в—Џ select partition 1: 1 represents the number of your system partition.
в—Џ active

в–Њ Method 4. Check internal hard disk status

If the internal hard disk has some disk errors, the «no bootable device found» error might pop out during Windows startup. You can check its status by CHKDSK.exe tool. To do so, you can refer to the method 3 to open Command Prompt window. Then execute command «chkdsk c: /f /x /r«, which will check errors on the C drive (the Windows operating system is usually installed on this drive) and fix them if possible.

в–Њ Method 5. Fix boot information (BCD and MBR)

When the boot information including BCD or MBR is corrupted by virus attack, power outage or bad sectors, you may get an error «no bootable devices found». You can repair or rebuild such crucial information through Command Prompt commands. Also, you need to first enter Command Prompt window, then execute bellow commands in order:

в–¶Bootrec /fixmbr
в–¶Bootrec /fixboot
в–¶Bootrec /scanos
в–¶Bootrec /rebuildbcd

Then restart your computer to check if this fixes your problem.

If you cannot access Command Prompt since the Windows installation DVD is not available, you can switch to AOMEI Partition Assistant Standard. With it, you can first create a bootable Windows 11/10/8/7 media, then boot your computer from it, and fix «no bootable device» problem. Besides this, you can also check disk and test disk speed with this tool.

Below are detailed steps on how to fix no bootable device via AOMEI Partition Assistant Standard.

Step 1. Plug an empty USB drive into a working computer, free download, install and run AOMEI Partition Assistant Standard on that PC.

Step 2. Click «Make Bootable Media» on the left side on the main interface, and follow the Wizard to create a bootable USB drive.

Then connect this bootable USB drive to your computer with «no bootable devices found» issue, and boot computer from the bootable media. When you log in, you will be in the main interface of AOMEI Partition Assistant Standard. Now you can rebuild MBR within three steps.

Step 1. Right-click the system hard disk, and select «Rebuild MBR».

Step 2. Choose an appropriate MBR type for your operating system, and click «OK».

Step 3. Hit on «Apply» and «Proceed» to commit the pending operation.

Furthermore, you can use this freeware to check system disk status: right click the system disk and select «Surface Test» and wait for the process to be finished.

Moreover, AOMEI Partition Assistant Standard also supports checking and fix partition errors: right click the system drive and select «Advanced»> «Check Partition», choose the first way to both check and repair partition errors….

в–Њ Method 6. Recover deleted boot partition

If you deleted your system partition by mistake and BIOS cannot find the boot drive, either, Windows will also fail to find the boot device. In this case, you can try AOMEI Partition Assistant Professional. It allows you to create a bootable media and recover deleted boot partition without loading up OS.

Step 1. Refer to the last method to make a bootable USB drive via the AOMEI Partition Assistant Pro. Boot the computer with no bootable device found from the created bootable media.

Step 2. In the main interface of AOMEI Partition Assistant Pro, click «All Tools» >»Partition Recovery Wizard»

Step 3. Choose a proper method to search for the deleted boot partition and click «Next».

Step 4. Choose the system disk and click «Next».

Step 5. Then you can choose the deleted system drive and click on «Proceed» to recover the lost boot partition.

Final words

As for how to fix no bootable device in Dell, Acer, HP and other computers with Windows 11/10/8/7 installed, these 6 methods are reported to be effective. I sincerely hope you will get a proper method according to your special situation. Apart from the above functions, AOMEI Partition Assistant also comes with many other great features: migrate OS to SSD, clone hard disk to another hard disk, extend system drive without reboot, etc.

Источник

No Bootable Device Found in Windows 10 — Solved Now!

Many users have come across an error that says “No bootable devices found” in Windows 10. If you are one of them, read this article and get the best solutions for it.

By Dervish / Last Updated March 10, 2022

Quick Navigation:

An error occurs: no bootable device found in Windows 10

Do you get annoyed because you can’t boot your computer only receiving a message “No bootable devices found”? A bootable device means any piece of hardware that contains or can read the files required for a computer to start. A hard drive, floppy disk drive, CD-ROM drive, DVD drive, and USB thumb drive are all considered bootable devices. How comes no bootable device found in Windows 10? Let’s get start.

How to fix no bootable device found in Windows 10 accordingly?

If you encounter no bootable device is detected, there are two possible causes. You can find corresponding solutions here. Windows installation media is needed for solution number 2. If you don’t have it, you can turn to a free tool offered in the next part.

Hard drive is not set as first boot device in BIOS

In this case, you can simply change boot order like this:

1. Restart computer and tap Del to enter BIOS interface.

2. Press the right arrow key on your keyboard until the Boot tab is opened. Move “Hard Drive” to the top of the boot order list by pressing “+” or “-”.

3. Press F10 to save changes and restart computer.

Tips:
в—Џ The function key to enter BIOS interface is likely to be F1, F2, F3, Esc, or Delete. If you are not sure, consult your PC manufacturer or go through your user manual.
в—Џ Since every BIOS setup utility is different, the menu option or configuration item might be called Boot, Boot Options, Boot Order, etc. The boot order option may even be located within a general menu option like Advanced Options, Advanced BIOS Features, or Other Options.

Corrupted MBR

Corrupted MBR can also lead to no boot device available in Windows 10. In this situation, you may repair MBR in following steps:

1. Insert the Windows installation media into your computer and boot from it.

2. Select the language and region, and then click on “Repair your computer” when you see the “Install now” window.

3. Select Troubleshoot and then Command Prompt on the Advanced options screen.

4. In Command Prompt, input following command lines and press Enter after each. (If you are asked whether you want to add a new installation to boot list, type “y” and then press Enter.)

в—Џ bootrec /fixmbr
в—Џ bootrec /fixboot
в—Џ bootrec /scanos
в—Џ bootrec /rebuildbcd

5. Exit Command Prompt and restart your computer.

Solve no bootable device found with free partition manager

If MBR of your computer is corrupted, you can also rebuild MBR with the best partition manager AOMEI Partition Assistant Standard. It is reliable and totally FREE. I’ll show you how to fix no bootable device in Windows 10 via AOMEI Partition Assistant step by step:

Step 1. Connect a USB drive to a computer in good condition. Download, install and run AOMEI Partition Assistant. Click on “Make Bootable Media” on the left-hand pane and follow the wizard to complete the process.

Tips: The bootable USB will contain installed AOMEI Partition Assistant.

Step 2. Insert the bootable USB into the computer which has a boot problem. Boot from the USB by changing boot order in BIOS.

Step 3. You’ll see loaded AOMEI Partition Assistant once login. Right click the system disk and select “Rebuild MBR”.

Step 4. Set the type of MBR for Window 10 in the pop-up window.

Step 5. Click “Apply” and then “Proceed” to commit the pending operations. Restart your computer later.

Summary

Now you have the best solutions for no bootable device found in Windows 10. They apply to no boot device found in Windows 7 as well. In addition to rebuilding MBR, you can also use AOMEI Partition Assistant to increase memory of C drive, erase SSD before selling and so on.

Источник